Solid wood tables are natural products of wood from the trees about 120 years. Wood is a living, and more moisture, more wood is the worktop. The wood is kiln dried wood with a moisture content of 6%, and therefore it is important that the work is not very humid. The algemeenal the humedadNIVEL in Kücheund is about 50-70%.
The top is solid wood box, die the Cabinet with wood screws and washers. Not recommended for the glue to the top of the box office, and the top of the field and will be based on different types of contracts, and could be extended to leaks that are likely in most of the surface of the housing.
The correct way to a solid wood with metal fasteners to mígabinete to the box (see our website).
Uniformementedistribuiti metal fasteners must be over the top,spaced at 1 "- 1.5 spaced. The width of the upper part is often at each metal bracket with three screws, one in the middle, one on the front and on the edge. The supports must be perfectly flat, because otherwise the tensiónpuede grow on wood, with a ontluchtingsinrichtingOSAS deformation or cracks.
It is advisable to pre-drill holes in Ho ut worktop to cracks and fractures. For the same reason, it is a good idea, not over tighten the screws. The goal ist significantly decreased the extent of these movements, but not completely eliminated. The construction of the composite panel, the duration of the movements are negligible, so that the installer should take care movements, the entire width of the panel. Con To prevent the development of internal tensions, the holes in the metal to be elongated in the direction of movement (see our website).
Wgallina exposed to normal humidity - ie 50-60% - the Arbeith the width is reduced by 1 / 12 "-1/24", but if a level of 80-90%, this measure may be to a maximum of 1 / 2 "or more cualquiery species. Therefore, if the edge of the meter is installed against a wall to the top, the wall around the top of the Natuurlijke movement, leading to undesired tensions in the wood. To avoid this, we have January 1 / 4 "-1 / 2" connection between the wall and the board worktop seal and a thin supply of silicon acid.
DarMoreover you can attach the edge of the metal and thus the natural movement verificaciónRSI at the expense of the other side.
In this case, in which the Danes holes in the metal, the rear portion of the plate should not exceed the diameter of the schroef, while the corresponding holes in the middle and the edge is elongated.
For more information about installing wood counter tops, bar tops and islands kitchit, visit our website.
The top is solid wood box, die the Cabinet with wood screws and washers. Not recommended for the glue to the top of the box office, and the top of the field and will be based on different types of contracts, and could be extended to leaks that are likely in most of the surface of the housing.
The correct way to a solid wood with metal fasteners to mígabinete to the box (see our website).
Uniformementedistribuiti metal fasteners must be over the top,spaced at 1 "- 1.5 spaced. The width of the upper part is often at each metal bracket with three screws, one in the middle, one on the front and on the edge. The supports must be perfectly flat, because otherwise the tensiónpuede grow on wood, with a ontluchtingsinrichtingOSAS deformation or cracks.
It is advisable to pre-drill holes in Ho ut worktop to cracks and fractures. For the same reason, it is a good idea, not over tighten the screws. The goal ist significantly decreased the extent of these movements, but not completely eliminated. The construction of the composite panel, the duration of the movements are negligible, so that the installer should take care movements, the entire width of the panel. Con To prevent the development of internal tensions, the holes in the metal to be elongated in the direction of movement (see our website).
Wgallina exposed to normal humidity - ie 50-60% - the Arbeith the width is reduced by 1 / 12 "-1/24", but if a level of 80-90%, this measure may be to a maximum of 1 / 2 "or more cualquiery species. Therefore, if the edge of the meter is installed against a wall to the top, the wall around the top of the Natuurlijke movement, leading to undesired tensions in the wood. To avoid this, we have January 1 / 4 "-1 / 2" connection between the wall and the board worktop seal and a thin supply of silicon acid.
DarMoreover you can attach the edge of the metal and thus the natural movement verificaciónRSI at the expense of the other side.
In this case, in which the Danes holes in the metal, the rear portion of the plate should not exceed the diameter of the schroef, while the corresponding holes in the middle and the edge is elongated.
For more information about installing wood counter tops, bar tops and islands kitchit, visit our website.
ไม่มีความคิดเห็น:
แสดงความคิดเห็น